| О фирме | Продажи | Каталоги | Справочник | Карта сайта |

Intel    Atmel    Dallas Semiconductor    Goal Semiconductor    Hyndai    Infineon    Philips    Temic    Winbond    Other

Специализированные микроконтроллеры с ядром 8051
Special 8051-Core Microcontrollers

Микроконвертеры фирмы Analog Devices

Analog Devices Microconverters


Part# MCU Core MCU Speed
(MIPS)
Flash
(kBytes)
SRAM
(bytes)
GPIO
Pins
ADC
Resolution
(bits)
ADC
Speed
(KSPS)
ADC
# Channels
12Bit DAC
Outputs
PWM
ADUC812 8052 (12-clk)1.38256341220082-
ADUC814 8052 (12-clk)1.38256181224762-
ADUC816 8052 (12-clk)1.3825634160.10541-
ADUC824 8052 (12-clk)1825634240.10541-
ADUC831 8052 (12-clk)1.3622304341224782Dual
ADUC832 8052 (12-clk)1.3622304341224782Dual
ADUC834 8052 (12-clk)162230434240.10541Dual
ADUC836 8052 (12-clk)162230434160.10541Dual
ADUC841 8052 (1-clk)20622304341240082Dual
ADUC842 8052 (1-clk)16622304341240082Dual
ADUC843 8052 (1-clk)1662230434124008-Dual
ADUC845 8052 (1-clk)1262230434241.37101Dual
ADUC847 8052 (1-clk)1262230434241.3710-Dual
ADUC848 8052 (1-clk)1262230434161.3710-Dual

Приемопередатчик фирмы Chipcon с ядром 8051

Chipcon Transceiver with 8051 microcontroller core


CC1010 - The industry's first truly complete RF System-on-Chip solution! On a single die, the award winning 300 to 1000 MHz CMOS CC1000 RF Transceiver has been integrated with an industry standard 8051 microcontroller core. The CC1010 integrates a very low-power 300 to 1000 MHz RF transceiver and a 8051-compatible microcontroller that has 32 kB in-system programmable Flash, hardware DES encryption/decryption and a three channel 10-bit ADC. This means only a few external passive components are necessary to make a powerful embedded system with wireless communication capabilities, sensor interfacing possibilities and a lot of processing power.


Features:

300-1000 MHz RF Transceiver
  • Very low current consumption
  • High sensitivity (typically -107 dBm)
  • Programmable output power up to +10 dBm
  • Data rate up to 76.8 kBit/s
  • Very few external components
8051-Compatible Microcontroller
  • Typically 2.5 times the performance of a standard 8051
  • 32 kB Flash, 2048 + 128 Byte SRAM
  • 3 channel 10 bit ADC, 4 timers /2 PWMs
  • 2 UARTs, RTC, Watchdog
  • SPI, DES encryption, 26 general I/O pins

Коммуникационный микроконтроллер CMX850 фирмы CML Microcircuits

CML Microcircuits Communications Controller CMX850


The CMX850 combines a dual-port V.22bis modem with an 8051 MCU including 8k of RAM to form a powerful communications processor. Extended addressing offers page-mode access to 4Mbytes of external FLASH memory. The 8051 runs from the ~12MHz oscillator with a choice of sub-multiple frequencies down to ~12kHz giving a range of low power operating modes.

The supply voltage is in the range: 3.0 to 3.6 V. A Watchdog Timer and standard 8051 Timers are included. I/O facilities include an LCD controller interface, 8x16 keypad interface with interrupts, a UART, two low power PWM outputs, and a multiplexed 2-input 10-bit A to D converter. Unused functions can be alternatively used as GPIO. Low power and very low power (sleep) modes contribute to low battery consumption.

The MUXAD pin allows the 8051 to multiplex the eight lower address and data bus lines to release further pins for I/O (debug support etc.). The V.22bis modem can be woken from sleep mode by 'ringing' or 'line-reversals'.


Features:

  • 8051µC with 8k RAM
  • Addressing for 4MB of External Flash Memory
  • External LCD Controller Interface 
  • V.22bis, V.22, V21 (and Bell equivalents) Integral Modem
  • Tx and Rx DTMF/Tones
  • Line and Phone Differential Amplifiers
  • Dual Clock Modes with Separate Xtals
  • Call Progress Decoder
  • CAS Tone Detection and Generation 
  • 'Line Reverse', 'Ring' and 'Off-Hook' Detection
  • LowPower Operation with 'Powersave' and 'Sleep' Modes
  • Watchdog Timer
  • GPI/O, UART and Timer Port with External Interrupts
  • Multiplexed 2-Input A-to-D Converter
  • Keypad (8x16) GPIO
  • 2 x Low Power PWM Outputs
  • Packages 100 pin LQFP.

Brief CMX850 Technical Overview

MinTypMax
Operating Voltage 3.0 to 3.6V
Typical Operating Current (3.3V) 5.8
15.0mA
Typical Powersave Current (3.3V) 30.0
100µA
Rx/Tx QAM and DPSK Modes V.22bis, V.22, Bell212A
Rx/Tx FSK Modes V.23, V.21, Bell202, Bell 103
Rx Modem Signal Level -45.0
-9.0dBm
Call Progress Energy Detect Threshold

-37.0dBm
DTMF Input Signal Levels -30.0
0dBm

Периферийный микроконтроллер P-51 фирмы Cybernetic Micro Systems

Cybernetic Micro Systems Peripheral 8051 System on a Chip


The P-51 "Peripheral 8051" is a new concept: An 8051 with built-in (E)ISA or PC-104 interface and supporting subsystems. These include downloadable Code RAM, dual port RAM, and all eleven IRQs to the host. Unlike classical 8051s, the P-51 naturally and easily interfaces to a host through simple standard buses, and its microsecond timing can provide real-time response to Windows applications.

P-51 Features

All 8051/52 resources:EISA/PC-104 interface:Special Features:
  • 8K bytes downloadable Code RAM
  • 256 bytes internal Data RAM
  • Timers 0, 1, and 2
  • Ports 0, 1, 2, and 3
  • All 8051 instructions
  • All 8051-equivalent Pins
  • Download Code RAM while reset
  • Execute Code when released
  • 45 EISA signals supported
  • Uses one of 11 IRQ pins
  • Software selectable IRQ 3-15
  • 20 ISA Address pins
  • 8 ISA Data Bus pins
  • Hardware or software Reset
  • Select Segment Addr 0 and A400 to EC00
  • Uses 16K bytes of system memory space,
    normally in an Upper Memory Block
  • 4K-byte dual port RAM shared by host and P-51
  • Dual Data Pointer
  • Square Root function
  • Debug capability
  • Breakpoint and single-step
  • Software interrupt generation
  • 3.3v 100-pin QFP
  • 5v I/O tolerant
  • 51 MHz operation

USB-микроконтроллеры фирмы Cypress с ядром 8051

Cypress 8051-core USB-microcontrollers


Cypress's EZ-USB family of full-speed USB microcontrollers feature an enhanced 8051 core running at 24 MHz, and a RAM-based architecture, enabling the download of firmware from the host PC. The EZ-USB family supports high-bandwidth applications by providing the maximum number of endpoints allowed by the USB specification, as well as an efficient mechanism to move data on or off chip. For data intensive applications like modems, scanners, printers, and cameras, the EZ-USB family is the premier solution.

For even higher performance full-speed USB applications, Cypress has released the EZ-USB FX family. Based on the same architecture that has made the EZ-USB family so successful, the FX family (which stands for Faster and Xtended) implements an 8051 core that runs at 48 MHz, a 16-bit external datapath supported by on-chip FIFOs, as well as a DMA engine. The FX family is the highest performance full-speed USB solution available--until high-speed USB comes on line next year with USB 2.0 (with signaling rates up to 480 Mbits/second)! The EZ-USB and EZ-USB FX families offer software compatibility, and EZ-USB FX provides an excellent migration path to USB 2.0 for your customers. The I/O side is already capable of the high-speed signaling rates.

All Cypress USB family members are supported by one of our comprehensive Development Kits. These kits are the fast track to developing firmware and driver software for USB peripherals. Examples complete with source code are included to provide the designer with fast time to market.

Features EZ-USB and EZ-USB FX Series
  • High-Performance I/O port
  • RAM Architecture--4/8 Kbytes
  • Enhanced 8051 Core
  • Pin and Software Compatible Family
  • I2C Controller
  • USB 1.1 Compliant

EZ-USB Full-Speed USB Microcontrollers

Part Number Core RAM Size EPROM Size Isochronous Support # I/Os Package
AN2121SC Enhanced 80514 KbyteN/AYes1644-pin PQFP
AN2122SC Enhanced 80514 KbyteN/ANo1644-pin PQFP
AN2122TC Enhanced 80514 KbyteN/ANo1948-pin TQFP
AN2125SC Enhanced 80514 KbyteN/AYes844-pin PQFP
AN2126SC Enhanced 80514 KbyteN/ANo844-pin PQFP
AN2126TC Enhanced 80514 KbyteN/ANo1148-pin TQFP
AN2131SC Enhanced 80518 KbyteN/AYes1644 pin PQFP
AN2135SC Enhanced 80518 KbyteN/AYes844 pin PQFP
AN2136SC Enhanced 80518 KbyteN/ANo844-pin PQFP
AN2131QC Enhanced 80518 KbyteN/AYes2480-pin PQFP

EZ-USB FX Full-Speed USB Microcontrollers

Part Number Core RAM Size EPROM Size Isochronous Support # I/Os Package
CY7C64601-52NC Enhanced 80514 KbyteN/ANo1652-pin PQFP
CY7C64603-52NC Enhanced 80518 KbyteN/ANo1652-pin PQFP
CY7C64613-52NC Enhanced 80518 KbyteN/AYes1652-pin PQFP
CY7C64603-80NC Enhanced 80518 KbyteN/ANo3280-pin PQFP
CY7C64613-80NC Enhanced 80518 KbyteN/AYes3280-pin PQFP
CY7C64603-128NC Enhanced 80518 KbyteN/ANo40128-pin PQFP
CY7C64613-128NC Enhanced 80518 KbyteN/AYes40128-pin PQFP


PowerBus микроконтроллеры фирмы Domosys

Domosys PowerBus Microcontrollers


Domosys sells several ICs that are powerful single-chip solutions for developing a complete PowerBus device. Each IC is based on a RISC 8051 microcontroller (8x faster than a standard 8051) operating at 30 MHz from –40°C to 85°C. They contain 64 KB of flash memory, 6 KB of RAM, a versatile PHY supporting multiple media (AC, DC, and TP), and are available in 48 and 80 pin LQFP packages.

The PowerBus protocol stack is embedded in the flash memory, and can be upgraded via UART, SPI, or the medium. Lots of room is available in flash memory for adding manufacturer or installer scenarios and applications using V-Logic and V^(2)s. Every chip has a unique, worldwide MAC address useful for addressing PB nodes over the Internet, as well as several unique 80-bit encryption keys. The U-510 and U-530 series of ICs contains support for operating as LN or SN managers, at the expense of not having any I/O device drivers other than the PowerBus API serial interface. The U-520 and U-540 series of ICs can only operate as a PB node, but contain drivers for up to 36 I/Os, a triac driver, 2 PWM outputs, and an input counter.



Микроконтроллер 83C51 фирмы Honeywell с широким температурным диапазоном

Honeywell High Temperature 83C51 Microcontroller


The HT83C51 is an affordable and highly reliable electronic component designed specifically for applications with an extremely wide operating temperature range such as down-hole oil well, aerospace, turbine engine and industrial control. The HT83C51 is a monolithic 8-bit microcontroller that provides guaranteed performance supporting operating frequencies in excess of 16MHz over the full -55 to +225 degrees Centigrade temperature range with reduced performance operation to +300 degrees Centigrade. These new pre-tested parts will last tens of thousands of hours at 225 degrees Centigrade.

The HTMOS family of products is fabricated with Honeywell's dielectrically isolated high temperature process designed specifically for severe high temperature environments. The HT83C51 uses the standard MCS-51 instruction set which is optimized for control applications and is compatible with all known development environments. Electronics can be placed with sensors to transmit high level signals to the main controller. Key features include the programmable counter array, watch dog timer, enhanced serial port for multiprocessor communication and a hierarchical interrupt structure.

Software selectable idle and power down modes are also included for reduced power. The HT83C51 supports half-duplex serial communication and has 8K Bytes of Mask programmable ROM. The device is available in a standard pinout DIP with optional packages considered.



12-разрядные системы сбора данных с микроконтроллером фирмы Maxim

Maxim Flash Programmable 12-Bit Integrated Data-Acquisition Systems


Description

The MAX7651/MAX7652 are complete 12-bit data-acquisition systems featuring an algorithmic, switched-capacitor, analog-to-digital converter (ADC), a pulse- width-modulated digital-to-analog converter (DAC), three timer/counters, and an industry-standard 8051 microprocessor core with a variety of I/O peripherals. Power-down capability and full functionality with supply voltages as low as +3V make the MAX7651/MAX7652 suitable for portable and power-sensitive applications.

The MAX7651/MAX7652 perform fully differential voltage measurements with 12-bit resolution, programmable gain, and separate track-and-hold for both positive and negative inputs. The converter accepts versatile input modes consisting of four 2-channel signal pairs or eight 1-channel signals relative to a floating common.

The MAX7651/MAX7652 microprocessor systems feature a CPU, 256 bytes of RAM, two 8kB flash memory, four 8-bit I/O ports, two UARTs, an interrupt controller, and a watchdog timer. Only four clock cycles are required to complete each microprocessor instruction.


Key Features
  • 12-Bit 53ksps ADC with Fully Differential Inputs
  • Dual 8-Bit PWM DAC Outputs
  • Three Timers
  • 4-Clock Cycle 8051-Compatible Instruction Set with Dual Data Pointers
  • Programmable Watchdog Supervisor
  • Four Parallel I/O Ports
  • Dual Serial I/O Ports (up to 375kb)
  • +3V or +5V Single-Supply Operation
  • DC to 12MHz Clock Speed
  • 64-Pin TQFP Package

Part Number FLASH Speed I/O Ports ADC CH ADC
Resolution
ADC Speed INL DNL DAC CH DAC
Resolution
Package Data
Sheet
MAX7651 2x8124812 Bits 53+/- 1.5+/- 12868-TQFP
MAX7652+/- 1


Специализированные микроконтроллеры с ядром 8051 фирмы Myson Century

Myson Century Special 8051-Core Microcontrollers


Product No. Product Description Product Status
CS8954General Purpose 8051 MCU 64K Flash Type with ISPSampling
MTV012A8051 Embedded CRT Monitor Controller (Mask Version)Production
MTV112A168051 Embedded CRT Monitor Controller (Mask Version)Production
MTV112A328051 Embedded CRT Monitor Controller (Mask Version)Production
MTV112M8051 Embedded CRT Monitor Controller (Flash Version)Production
MTV212A328051 Embedded CRT Monitor Controller (Mask Version)Production
MTV212M328051 Embedded CRT Monitor Controller (MTP+ISP)Production
MTV212M648051 Embedded CRT Monitor Controller (MTP Version)Production
MTV212M64i8051 Embedded CRT Monitor Controller (MTP+ISP)Production
MTV230M648051 Embedded LCD Monitor Controller with Flash OSD 3.3V MTP+ISPProduction
MTV312A648051 Embedded Monitor Controller (3.3/5V Mask Version)Sampling
MTV312M648051 Embedded Monitor Controller Flash Type with ISPProduction
MTV313A8051 Embedded CRT Controller with 32K MaskDevelopment
MTV313M8051 Embedded LCD Monitor Controller with 64K FlashSampling
MTV412M8051 Embedded LCD Monitor Controller with 128K Flash+ISPProduction
MTV415M8051 Embedded Micro-Controller with 128K Flash ROMDevelopment
MTV512M8051 Embedded Monitor Controller 64K Flash Type with ISPSampling
CS6208General Purpose 8-Bit Microcontroller /w Embedded Internet AccessSampling
MTP8058051 Embedded USB/PS2 Keyboard/Mouse ControllerProduction
MTP805A8051 Embedded USB/PS2 Keyboard/Mouse ControllerDevelopment
MTP805M8051 Embedded USB/PS2 Keyboard/Mouse ControllerProduction

Микроконтроллеры фирмы Philips с расширенной 16-разрядной архитектурой

Philips Semiconductors 16-bit XA Microcontrollers


Philips high-performance 16-bit eXtended Architecture (XA) offers high code density plus source level code compatibility with the 80C51. XA features include 3V operation with low power consumption and power management capabilities together with extended instruction set and 16MB address range.


Part
Number
Memory Timer/Counters I/O Serial Special Features A/D Inter-
rupts
Max
Freq.
Package
  Flash OTP RAM # PWM PCA WD Pins Interfaces   Bits (Ext.) (MHz)  
XAC37  32K10243NNY32UART,SPI CAN 2.0B/PeliCAN/
CAN Transport Layer
 42(3)32A44,BD44
XAG30  32K5123NNY322 UARTs 2.7V-5.5V,80C51 Upgrade 38(3)30A44,BD44
XAG37  32K5123NNY322 UARTs 2.7V-5.5Voperation,80C51 Upgrade 38(3)30A44,B44
XAG39 32K 10243NNY;322 UARTs 5V operation,80C51 Upgrade 38(3)30A44
XAG49 64K 20483NNY;322 UARTs 5V operation,80C51 Upgrade 38(3)30A44,BD44
XAH3   2562NNY324 UARTs Minimal external
components needed
 42(3)30B100
XAH4   2562NNY324 USARTs On-board DRAM controller 42(3)30B100
XAS3  32K10244YYY502 UARTs,I2C 16M byte address range,2.7-5.5V,8-bit ADC846(2)30A68,B80


SoC (System-on-Chip) фирмы Siliconians для беспроводой коммуникации

Siliconians System-on-Chip for wireless communication


SS1102 is an integration of SS1101 and an 8-bit micro-controller on a single chip. The CPU is code compatible with Intel 80C51. You can build a compact wireless communication module (WCM) with an RF module and SS1102 (two components). Because SS1102 has a CPU inside, the software code may reside on an internal mask ROM or in an external ROM chip. For the external ROM chip configuration, SS1102 is packaged in 100-pin TQFP which allows extra pins for ROM interface. For the internal ROM configuration, the chip comes in 52-pin QFP and is called SS1119.


Микроконтроллер с сетевым интерфейсом фирмы Standard Microsystems

Standard Microsystems Integrated Microcontroller and Network Interface


General Description. The COM20051 is a low-cost, highly-integrated microcontroller incorporating a high-performance network controller based on the ARCNET Token Bus Standard (ANSI 878.1). The COM20051 is based around the popular Intel 8051 architecture. The device is implemented using a microcontroller core compatible with the Intel 80C32 ROMless version of the 8051 architecture. The COM20051 is ideal for distributed control networking applications such as those found in industrial/machine controls, building/factory automation, consumer products, instrumentation and automobiles.
The COM20051 contains many features that are beneficial for embedded control applications. The microcontroller is a fully-functional 16 MHz 80C32 that is compatible with the Intel 80C32 with two timers. In contrast to other embedded controller/networking solutions, the COM20051 adds a fully-featured, robust, powerful, and simple network interface while retaining all of the basic 8051 peripherals, such as the serial port and counter/timers.


Part
Number
RevisionPackageTemperature Power
Supply
ISA
Bus
Data RateRAM Micro-
controller
Maximum
Packet
Size
Duplicate
Note ID
8051
Peripheral
Interface
COM20051Rev. BPLCC440 - +70°C+5V8 Bit 156Kbps - 5Mbps1Kx88032507 Bytesxx
COM20051IRev. APLCC44-40 - +85°C+5V8 Bit 156 Kbps - 5 Mbps1Kx88032507 Bytesxx
Features
  • High Performance/Low Cost
  • Intel 8051 Instruction Set Compatible
  • Network Supports up to 255 Nodes
  • Maximum 507 Byte Packets
  • Self-Configuring Network Protocol
  • Utilizes ARCNET Token Bus Network Engine
  • 5 Mbps to 156 Kbps Network Data Rate
  • Receive All Mode Allows Any Packet to Be Received
  • Microcontroller Based on Popular 8051 Architecture
  • Drop-In Replacement for 80C32 PLCC
  • Powerful Network Diagnostics
  • Duplicate Node ID Detection
  • Retains all 8051 Peripherals Including Serial I/O and Two Timers
  • Requires No Special Emulators
  • Network Interface Supports RS-485, Twisted Pair, Coaxial and Fiber Optic Interfaces

Flash память c микроконтроллером 8052 фирмы STMicroelectronics

STMicroelectronics Flash Programmable System Devices with 8052 Microcontroller


The µPSD323X Devices combine a Flash PSD architecture with an 8032 microcontroller core. The µPSD323X Devices of Flash PSDs feature dual banks of Flash memory, SRAM, general purpose I/O and programmable logic, supervisory functions and access via USB, I2C, ADC, DDC and PWM channels, and an on-board 8032 microcontroller core, with two UARTs, three 16-bit Timer/Counters and two External Interrupts. As with other Flash PSD families, the µPSD323X Devices are also in-system programmable (ISP) via a JTAG ISP interface.

Summary Description

  • Dual bank Flash memories
    • Concurrent operation, read from memory while erasing and writing the other. In-Application Programming (IAP) for remote updates
    • Large 128KByte or 256KByte main Flash memory for application code, operating systems, or bit maps for graphic user interfaces
    • Large 32KByte secondary Flash memory divided in small sectors. Eliminate external EEPROM with software EEPROM emulation
    • Secondary Flash memory is large enough for sophisticated communication protocol (USB) during IAP while continuing critical system tasks
  • Large SRAM with battery back-up option
    • 8KByte SRAM for RTOS, high-level languages, communication buffers, and stacks
  • Programmable Decode PLD for flexible address mapping of all memories
    • Place individual Flash and SRAM sectors on any address boundary
    • Built-in page register breaks restrictive 8032 limit of 64KByte address space
    • Special register swaps Flash memory segments between 8032 "program" space and "data" space for efficient In-Application Programming
  • High-speed clock standard 8032 core (12-cycle)
    • 40MHz operation at 5V, 24MHz at 3.3V
    • 2 UARTs with independent baud rate, three 16-bit Timer/Counters and two External Interrupts
  • USB Interface (µPSD3234A-40 only)
    • Supports USB 1.1 Slow Mode (1.5Mbit/s)
    • Control endpoint 0 and interrupt endpoints 1 and 2
  • I2C interface for peripheral connections
    • Capable of master or slave operation
  • 5 Pulse Width Modulator (PWM) channels
    • Four 8-bit PWM units
    • One 8-bit PWM unit with programmable period
  • 4-channel, 8-bit Analog-to-Digital Converter (ADC) with analog supply voltage (VREF)
  • Standalone Display Data Channel (DDC)
    • For use in monitor, projector, and TV applications
    • Compliant with VESA standards DDC1 and DDC2B
    • Eliminate external DDC PROM
  • Six I/O ports with up to 46 I/O pins
    • Multifunction I/O: GPIO, DDC, I2C, PWM, PLD I/O, supervisor, and JTAG
    • Eliminates need for external latches and logic
  • 3000 gate PLD with 16 macrocells
    • Create glue logic, state machines, delays, etc.
    • Eliminate external PALs, PLDs, and 74HCxx
    • Simple PSDsoft Express software ...Free
  • Supervisor functions
    • Generates reset upon low voltage or watchdog time-out. Eliminate external supervisor device
    • RESET Input pin; Reset output via PLD
  • In-System Programming (ISP) via JTAG
    • Program entire chip in 10 - 25 seconds with no involvement of 8032
    • Allows efficient manufacturing, easy product testing, and Just-In-Time inventory
    • Eliminate sockets and pre-programmed parts
    • Program with FlashLINKTM cable and any PC
  • Content Security
    • Programmable Security Bit blocks access of device programmers and readers
  • Zero-Power Technology
    • Memories and PLD automatically reach standby current between input changes
  • Packages
    • 52-pin TQFP
    • 80-pin TQFP: allows access to 8032 address/data/control signals for connecting to external peripherals

Part No Main
Flash
bit
Sec
Flash
bit
SRAM
bit
Macro-
Cells
I/O
Pins
PWM
Ch.
Timer
/Ctr
UART
Ch.
I2C ADC
Ch.
DDC USB Vcc MHz Pins
µPSD3234A-40 2M256K64K1637 or 465321 4YY5V4052 or 80
µPSD3234BV-40 2M256K64K16465321 4Y3V2480
µPSD3233A-40 1M256K64K1637 or 465321 4Y5V4052 or 80
µPSD3233BV-40 1M256K64K16465321 4Y3V2480

Микроконтроллер 73M2910L фирмы TDK с архитектурой MCS-51

TDK 8051-Arhitecture Microcontroller 73M2910L


The 73M2910L high performance micro-controller is based on the industry standard 8-bit 8032. The architecture has been optimized for low power portable modem or communication applications by integrating unique features with the core CPU.

A key feature is a user friendly HDLC Packetizer, accessed through the special function registers. It has a serial I/O, hardware support for 16 and 32-bit CRC, zero insert/delete control, a dedicated interrupt and a clear channel mode for by-passing the packetizer.

The 73M2910L has two extra interrupt sources, an external interrupt and a HDLC interrupt. The HDLC interrupt has two registers associated with it; the HDLC Interrupt Register which is used to determine the source of the interrupt, and the HDLC Interrupt Enable Register that enables the source of the interrupt.

The state of the external interrupts can be read through a register allowing the interrupt pins to be used as inputs. The interrupt pins INT0 and INT1 can be either negative edge, positive edge or level triggered. The INT2 pin is always edge triggered.

Two buffered clock outputs have been added to support peripheral functions such as UARTs, modems and other clocked devices.

Additional internal special function registers are used for firmware control over the HDLC Packetizer, the clocks and the programmable I/O ports.

For low power applications the 73M2910L supports two power conservation modes: idle and power-down.


Features
  • 8032 compatible instruction set
  • 44 MHz Operation from 3.3 to 5.5V
  • HDLC support logic (Packetizer, 16 and 32 CRC, zero ID)
  • 24 pins for user programmable I/O ports
  • 8 pins programmable chip select logic or I/O for memory mapped peripheral eliminating glue logic
  • 3 external interrupt sources (programmable polarity)
  • 16 dedicated latched address pins
  • Multiplexed data/address bus
  • Instruction cycle time identical to 8032
  • Buffered oscillator (or OSC/2) output pin
  • 1.8432 MHz UART clock available
  • Bank select circuitry to support up to 128k of external program memory
  • Also available in 100-pin QFP and 100-pin TQFP

Микроконвертеры с микроконтроллером 8051 фирмы Texas Instruments

Texas Instruments MicroSystem Mixed-Signal Data Converters


Device Name Power
Typ
(mW)
Supply
(V)
Data-Bus
Interface
(bits)
Vref
(Int/Ext)
Pin/
Package
Description
MSC1200Y2 42.7-5.5Parallel/SerialInt/Ext48TQFP 8051 CPU with 4kB Memory, 24-Bit ADC, Current DAC, and On-Chip Oscillator
MSC1200Y3 42.7-5.5Parallel/SerialInt/Ext 48TQFP8051 CPU with 8kB Memory, 24-Bit ADC, Current DAC, and On-Chip Oscillator
MSC1201Y2 42.7-5.5Parallel/SerialInt/Ext 36QFN8051CPU with 4kB Memory, 24-Bit ADC, Current DAC, and On-Chip Oscillator
MSC1201Y3 42.7-5.5Parallel/SerialInt/Ext 36QFN8051 CPU with 8kB Memory, 24-Bit ADC, Current DAC, and On-Chip Oscillator
MSC1202Y2 42.7-5.5Parallel/SerialInt/Ext 36QFN8051 CPU with 4kB Memory, 16-Bit ADC, Current DAC, and On-Chip Oscillator
MSC1202Y3 42.7-5.5Parallel/SerialInt/Ext 36QFN8051 CPU with 8kB Memory, 16-Bit ADC, Current DAC, and On-Chip Oscillator
MSC1210Y2 42.7-5.5Parallel/SerialInt/Ext 64TQFPPrecision Analog-to-Digital Converter (ADC) with 8051 MCU and 4k Flash Memory
MSC1210Y3 42.7-5.5Parallel/SerialInt/Ext 64TQFPPrecision Analog-to-Digital Converter (ADC) with 8051 MCU and 8k Flash Memory
MSC1210Y4 42.7-5.5Parallel/SerialInt/Ext 64TQFPPrecision Analog-to-Digital Converter (ADC) with 8051 MCU and 16k Flash Memory
MSC1210Y5 42.7-5.5Parallel/SerialInt/Ext 64TQFPPrecision Analog-to-Digital Converter (ADC) with 8051 MCU and 32k Flash Memory
MSC1211Y2 42.7-5.5Parallel/SerialInt/Ext 64TQFP8051 CPU with 4kB Memory, I2C, 24-Bit ADC, and Quad 16-Bit DACs
MSC1211Y3 42.7-5.5Parallel/SerialInt/Ext 64TQFP8051 CPU with 8kB Memory, I2C, 24-Bit ADC, and Quad 16-Bit DACs
MSC1211Y4 42.7-5.5Parallel/SerialInt/Ext 64TQFP8051 CPU with 16kB Memory, I2C, 24-Bit ADC, and Quad 16-Bit DACs
MSC1211Y5 42.7-5.5Parallel/SerialInt/Ext 64TQFP8051 CPU with 32kB Memory, I2C, 24-Bit ADC, and Quad 16-Bit DACs
MSC1212Y2 42.7-5.5Parallel/SerialInt/Ext 64TQFP8051 CPU with 4kB Memory, 24-Bit ADC, and Quad 16-Bit DACs
MSC1212Y3 42.7-5.5Parallel/SerialInt/Ext 64TQFP8051 CPU with 8kB Memory, 24-Bit ADC, and Quad 16-Bit DACs
MSC1212Y4 42.7-5.5Parallel/SerialInt/Ext 64TQFP8051 CPU with 16kB Memory, 24-Bit ADC, and Quad 16-Bit DACs
MSC1212Y5 42.7-5.5Parallel/SerialInt/Ext 64TQFP8051 CPU with 32kB Memory, 24-Bit ADC, and Quad 16-Bit DACs
MSC1213Y2 42.7-5.5Parallel/SerialInt/Ext 64TQFPPrecision A/D & D/A with 8051 MCU and Flash Memory
MSC1213Y3 42.7-5.5Parallel/SerialInt/Ext 64TQFPPrecision A/D & D/A with 8051 MCU and Flash Memory
MSC1213Y4 42.7-5.5Parallel/SerialInt/Ext 64TQFPPrecision A/D & D/A with 8051 MCU and Flash Memory
MSC1213Y5 42.7-5.5Parallel/SerialInt/Ext 64TQFPPrecision A/D & D/A with 8051 MCU and Flash Memory
MSC1214Y2 42.7-5.5Parallel/SerialInt/Ext 64TQFPPrecision A/D & D/A with 8051 MCU and Flash Memory
MSC1214Y3 42.7-5.5Parallel/SerialInt/Ext 64TQFPPrecision A/D & D/A with 8051 MCU and Flash Memory
MSC1214Y4 42.7-5.5Parallel/SerialInt/Ext 64TQFPPrecision A/D & D/A with 8051 MCU and Flash Memory
MSC1214Y5 42.7-5.5Parallel/SerialInt/Ext 64TQFPPrecision A/D & D/A with 8051 MCU and Flash Memory

Микроконтроллеры семейства E5 фирмы Triscend с ядром 8051

Triscend 8051-core E5 Family Microcontrollers


The Triscend E5 family is based on a performance-enhanced "turbo" version of the 8032 8-bit microcontroller. The E5 Family consists of 4 devices (all based on the "turbo" 8032) which vary in the amount of on-chip programmable logic, RAM and I/Os.

The E5 is ideal for embedded systems applications that demand both time-to-market and high levels of customization. The E5 is compatible with existing, third-party 8032 firmware tools--from code development to in-system, real-time debugging. Thus a designer can utilize familiar processor development tools and code libraries.

Designers can configure E5 CSoC chips using the Triscend FastChip Development System. FastChip software allows designers to customize the processor peripherals using a "drag and drop" methodology. Designers simply select which soft peripheral is desired, then they "drag" it into place around the processor. From there FastChip makes the rest of the process automatic--code development can proceed without worrying about the implementation details of the soft peripheral.
E5 Highlights

  • High performance 8032 (10 MIPS at 40 MHz)
  • Binary and source code compatible with other 8032/8052 variants
  • Standalone operation from a single external memory (code + configuration)
  • Up to 64Kbytes of on-chip, dedicated system RAM
  • Up to 3200 Configurable System Logic (CSL) cells (up to 40,000 "ASIC" gates)
  • Power-down and power-management modes (low power mode consumption under 100 uA)
  • Compliant to the "CSI Socket" interface, allowing soft peripherals to be used on other CSoC Families
  • Two dedicated DMA Channels
  • On-chip breakpoint unit provides sophisticated debugging capability

Part Number Timer/
Counters
WDT UARTs On-Chip
MOVX
SRAM
DMA
Channels
Max.
User
I/O
CSL Address
Decoders
Bus
Speed
MHz
Packaging
CellsGate Count
E505 3x16-bit1116K x 82124 512~6,500 gates3225, 40PQFP128,PQFP208
E512 3x16-bit1116K x 82150 1,152~15,000 gates7225, 40PQFP128,PQFP208
E520 3x16-bit1140K x 82252 2,048~26,000 gates12825, 40PQFP208,BGA436
E5323x16-bit1164K x 82316 3,200~40,000 gates20025, 40PQFP208,BGA436

CSL = Configurable System Logic. Implements any possible logic function with four or less inputs plus a flip-flop. Also can be used as a 16x1 ROM or RAM. Also can be used an 8x1 dual-port RAM or a 8-bit serial-in/serial-out shift register.

The embedded programmable logic is ideal for adding peripherals. Triscend's FastChip development system allows a designer to drag-and-drop functions from a pre-defined library or to custom create functions using standard logic design tools such as schematic capture or logic synthesis.
Standard Features Include:

  • 256 bytes direct RAM
  • Up to 40K gates of SRAM-based programmable logic
  • Up to 64K bytes of XDATA RAM
  • Wait-state support
  • Two-channel DMA controller
  • Built-in glue-less memory interface to standard byte-wide FLASH memory
  • Up to 3 times faster than original 8051/52 at the same clock frequency
  • Supported by leading compilers, assemblers, and debuggers
  • High-performance internal peripheral bus
  • Power management
  • Hardware debugger

Микроконтроллеры фирмы Trumpion Microelectronics с ядром 8051

Trumpion Microelectronics 8051-core MP3 Microcontrollers


MP3 Microcontroller T33510. Trumpion Microelectronics (TMI) announces a new microcontroller T33510, which can be used in the applications of MP3 player, Flash Card Reader/Writer or USB to IDE converter. T33510 includes a popular 8051 CPU and is easy firmware development by ICE. This microcontroller uses 0.5um/3.3V process and its CPU speed has 3 frequencies, 6/12/24MHz, to be selected for low power consumption and high speed data transfer. The micocontroller has 32 general IO ports with extra address and data bus to access the user definded program.

USB-MMC microcontroller T33520. A new powerful USB-MMC microcontroller, named T33520, is developed for the applications of Memory card Read-Writer and MPEG-AUDIO player. T33520 includes a popular 8051 CPU and is easy firmware development by ICE. This microcontroller uses 0.35um/3.3V process and its CPU speed has 3 frequencies, 6/12/24MHz, to be selected for low power consumption and high speed data transfer. Using T33520 MMC interface controller can satisfy full MultiMediaCard bus protocol and full speed data rate(above 12 MHz) with up to 10 cards at very low power consumption.

Digital-Photo-Frame Controller T33530J. T33530J is a high integrated chip with 8051, Flash-card/memory interfaces, USB function 1.1, and JPEG decoder. The JPEG decoder can support VGA, SVGA or more for your need. The output of JPEG is a fast parallel interface to trumpion's LCD controller (Zipr/ZiproTC 0944/0946) which will connect to LCD panel.

CD-audio/MP3/WMA embedded flash controller T3160. T3160 is a powerful embedded flash micocontroller of easy firmware development, programmable integration flexibility, low power consumption and high anti-shock performance for CD player of audio, MP3, WMA or other format. T3160 has an embedded flash (64K bytes) with ISP (In System Programming) function built-in, and it is a popular 8051 based 8-bit micocontroller. User can have the flexibility to update firmware easily without external programmer and pull out the chip from system. The built-in 2-wire ISP channels are fast in downloading the user's program inside the chip within 5 seconds.


Микроконтроллер ZW0102 фирмы Zensys с ядром 8051

Zensys 8051-core ZW0102 Z-Wave Single Chip Microcontrollers


The ZW0102 Z-Wave™ Single Chip is an advanced implementation of Zensys' Z-Wave wireless control networking technology offering a lower cost, lower power consumption, and smaller form factor solution.

Zensys' Single Chip solution is specially suited for control and status reading applications including lighting, HVAC, and appliance control, while the optional security capabilities through HW encryption support and SW authentication/key-exchange is suited for sensors, alarm systems, automatic meter reading and energy management systems.

The ZW0102 is a mixed signal chip integrating RF transceiver, Z-Wave protocol storage and handling, and OEM product application storage and handling in one single chip. An on-chip 8 bit CPU core handles both the OEM application as well as the wireless communication protocol. Up to 20k byte of available flash memory gives the OEM the opportunity to download and run just about any control application directly on the Z-Wave Single Chip. This eliminates the need for an additional micro controller and external Flash memory for application code storage.
ZW0102 Features:

  • Mixed Signal IC With 8051 MCU Core And RF Transceiver In A Single Chip
  • Low Cost For Use In Mass Market Products
  • Reliable Wireless Communication
  • HW Supported Encryption Capabilities
  • Future Proof And Versatile For Integration Into Any Product